AE-TECHRON 8630 AMPLIFIER, 208V-415V, 30 kW (up to 120 kVA)
Key Performance Capabilities:
30 kW (up to 120 kVA), up to 240A continuous
- Bandwidth: DC to 50 kHz
- Voltage: 0 to 260 VRMS; 0 to 400 VDC
- Slew rate: Up to 80 V/µs
- Current: Up to 240 ARMS*
- Distortion: <0.2%
- Power: 30 kW*
- Power levels up to 2X rated power when driving reactive loads
- High power efficiency and density
Models available with output power from 10 kW to 60 kW (capable of up to 120 kVA).
Documents and Software Solutions:
HIGLIGHTS
AE Techron’s 8600 Series amplifiers are 400Vp, low-noise, DC-to-50 kHz switch-mode amplifiers. The 8600 series provides a unique combination of switch-mode and linear amplifier abilities. Switchmode efficiency is combined with what are typically benefits of linear amplifiers, low noise floor and THD, high slew rates, and wide bandwidth. The 8600 series is also able to safely drive both reactive and resistive loads of varying impedances with no loss in rated output power. 8600 series amplifiers pack a lot of power into a small package. They are able to produce surge power ratings at up to 20kW, and process apparent power at levels up to 2X the continuous power ratings. This makes an 8600 series amplifier an ideal choice for applications that require wide bandwidth, high power and great value. The 8600 series is also AC and DC capable, useful for producing power with quick surges or drop-outs, like those required for conducted immunity testing of AC or DC power systems found in military, commercial, or general aviation.
Common Data (all models)
- Operating Modes: AC, DC and AC + DC
- Frequency, AC Mode Output (-3 dB): DC – 50 kHz
- Max Voltage Ranges (no load),
- AC: 0 – 260 VRMS
- AC + DC: 0 – ±400 VP
- Load Regulation (full scale): <0.025%, DC to 100 Hz; <0.05%, 10 Hz to 10 kHz
- Line Regulation (full scale): <0.1% for 10% line change
- External Sense: Voltage-drop compensation sense line
- Harmonic Distortion (80 kHz, low-passed): Less than 0.3% from 10 Hz to 30 kHz; 0.5% up to 50 kHz
- Harmonic Distortion (30 kHz, low-passed): Less than 0.1% from 10 Hz to 50 kHz
- DC Offset: <10 mV
- Distortion: <0.2%
- Voltage Slew Rate: Load dependent; up to 80V per μs, typically 10 μs to 30 μs for 10% to 90% of full-scale change, depending on load and power
- Efficiency: 89%, typical
- Power Factor: .92, typical
- Cooling: Internal forced-air fans
- Protection: Over/under voltage, over current, over temperature
- Input, Signal In: BNC connector (unbalanced); terminal strip (balanced)
- Output: 3/8-inch high-current post connectors
- Operating Environment,
- Temperature: 5 °C to 50 °C (41 °F to 122 °F);
- Maximum output power de-rated above 30 °C (86 °F)
- Humidity: Maximum relative humidity 80% for
- temperatures up to 31 °C decreasing linearly
- to 50% relative humidity at 40 °C
- Altitude: 3000 m Maximum
- Environment: Indoor Use Only, Pollution degree 2
- Equipment Class: Group 1 Class A
- Transient Overvoltage: Overvoltage Category II
HIGLIGHTS
AE Techron’s 8600 Series amplifiers are 400Vp, low-noise, DC-to-50 kHz switch-mode amplifiers. The 8600 series provides a unique combination of switch-mode and linear amplifier abilities. Switchmode efficiency is combined with what are typically benefits of linear amplifiers, low noise floor and THD, high slew rates, and wide bandwidth. The 8600 series is also able to safely drive both reactive and resistive loads of varying impedances with no loss in rated output power. 8600 series amplifiers pack a lot of power into a small package. They are able to produce surge power ratings at up to 20kW, and process apparent power at levels up to 2X the continuous power ratings. This makes an 8600 series amplifier an ideal choice for applications that require wide bandwidth, high power and great value. The 8600 series is also AC and DC capable, useful for producing power with quick surges or drop-outs, like those required for conducted immunity testing of AC or DC power systems found in military, commercial, or general aviation.
Common Data (all models)
- Operating Modes: AC, DC and AC + DC
- Frequency, AC Mode Output (-3 dB): DC – 50 kHz
- Max Voltage Ranges (no load),
- AC: 0 – 260 VRMS
- AC + DC: 0 – ±400 VP
- Load Regulation (full scale): <0.025%, DC to 100 Hz; <0.05%, 10 Hz to 10 kHz
- Line Regulation (full scale): <0.1% for 10% line change
- External Sense: Voltage-drop compensation sense line
- Harmonic Distortion (80 kHz, low-passed): Less than 0.3% from 10 Hz to 30 kHz; 0.5% up to 50 kHz
- Harmonic Distortion (30 kHz, low-passed): Less than 0.1% from 10 Hz to 50 kHz
- DC Offset: <10 mV
- Distortion: <0.2%
- Voltage Slew Rate: Load dependent; up to 80V per μs, typically 10 μs to 30 μs for 10% to 90% of full-scale change, depending on load and power
- Efficiency: 89%, typical
- Power Factor: .92, typical
- Cooling: Internal forced-air fans
- Protection: Over/under voltage, over current, over temperature
- Input, Signal In: BNC connector (unbalanced); terminal strip (balanced)
- Output: 3/8-inch high-current post connectors
- Operating Environment,
- Temperature: 5 °C to 50 °C (41 °F to 122 °F);
- Maximum output power de-rated above 30 °C (86 °F)
- Humidity: Maximum relative humidity 80% for
- temperatures up to 31 °C decreasing linearly
- to 50% relative humidity at 40 °C
- Altitude: 3000 m Maximum
- Environment: Indoor Use Only, Pollution degree 2
- Equipment Class: Group 1 Class A
- Transient Overvoltage: Overvoltage Category II