ETS-8000-013 RF Power Amplifier, 500W, 80 MHz to 1 GHz, for IEC/EN 61000-4-3, 30 V/m
ETS-Lindgren's Model 8000-013 RF Power Amplifier is a 500W power amplifier, designed primarily for EMC applications that include IEC/EN 61000-4-3, 30 V/m requirements.
Key Features
- IEC/EN 61000-4-3, 30 V/m
- High Reliability Silicon LDMOS Design
- Front Panel or Remote control via Ethernet, GPIB, USB
- Excellent Performance and Efficiency
- Safety Interlock
Physical Specifications
- Dimensions: 19 in, 16U, 800 mm (34.6 in) Deep
- Weight: 98 kg (216 lb)
- Connector Types: Input (Nf) and Output (7/16)
- Case Style (Standard): Rack with Rear Panel Connectors
Electrical Specifications
- Electrical Frequency Range: 80 MHz to 1 GHz
- Nominal Output Power: 80-400 MHz (500W) ; 400 - 750 (400W) and 750 MHz-1 GHz (300W)
- Gain Variation: 3 dB
- Max Input Power : 10 dBm
- Harmonics: -20 dBc Maximum
- Output Impedance: 50
- Input VSWR: 1.5:1 Maximum
- AC Supply: Single Phase 200-240 Vac
- Supply Frequency Range: 50/60 Hz
- Line Power: <4 kVA
Additional Documents:
ETS-Lindgren's Model 8000-013 RF Power Amplifier is a 500W power amplifier, designed primarily for EMC applications that include IEC/EN 61000-4-3, 30 V/m requirements.
Utilizing Silicon LDMOS technology, this RF amplifier provides high linearity, rugged design and better efficiency performance..
The 8000-013 provides very low distortion and tolerance for 100% mismatch.
The ETS-Lindgren Model 8000-013 RF Power Amplifier is capable of supplying a minimum of 600 watts into a 50 ohm load over the frequency range 80MHz to 1000MHz. The amplifier is designed with sufficient gain so that it may be used with normal output levels of signal sources.
A safety interlock on the rear panel is also provided, which will mute the amplifier when grounded.
The unit is powered by a switched mode power supply for high efficiency, high power factor, and a wide voltage range operation. The unit is air cooled with integral fans and is protected against faulty cooling by excess temperature sensing.
A front panel fault indicator is provided to indicate over-temperature.
The amplifier is designed for rugged operation into a variety of loads and is primarily intended for use as an RF power source for EMC susceptibility testing, but is also applicable to other systems requiring a wide-band linear amplifier.
ETS-Lindgren's Model 8000-013 RF Power Amplifier is a 500W power amplifier, designed primarily for EMC applications that include IEC/EN 61000-4-3, 30 V/m requirements.
Utilizing Silicon LDMOS technology, this RF amplifier provides high linearity, rugged design and better efficiency performance..
The 8000-013 provides very low distortion and tolerance for 100% mismatch.
The ETS-Lindgren Model 8000-013 RF Power Amplifier is capable of supplying a minimum of 600 watts into a 50 ohm load over the frequency range 80MHz to 1000MHz. The amplifier is designed with sufficient gain so that it may be used with normal output levels of signal sources.
A safety interlock on the rear panel is also provided, which will mute the amplifier when grounded.
The unit is powered by a switched mode power supply for high efficiency, high power factor, and a wide voltage range operation. The unit is air cooled with integral fans and is protected against faulty cooling by excess temperature sensing.
A front panel fault indicator is provided to indicate over-temperature.
The amplifier is designed for rugged operation into a variety of loads and is primarily intended for use as an RF power source for EMC susceptibility testing, but is also applicable to other systems requiring a wide-band linear amplifier.