AR-150W1000B 150 Watt CW, 80 - 1000 MHz
RATED OUTPUT POWER: 160 watts typical, 130 watts minimum
INPUT FOR RATED OUTPUT: 1.0 mW Max
POWER OUTPUT @ 3dB COMPRESSION: Typical: 150 watts, Minimum: 125 watts
POWER OUTPUT @ 1dB COMPRESSION: ;Typical: 125 watts, Minimum: 100 watts
FLATNESS: ±1.5 dB typical, ±2.0 dB maximum
FREQUENCY RESPONSE: 80MHz-1000 MHz instantaneously
GAIN (at maximum setting): 52 dB minimum
GAIN ADJUSTMENT (Continuous Range) : 25 dB minimum (4096 steps remote)
INPUT IMPEDANCE: 50 ohms, VSWR 1.5:1 maximum: 1.3:1 typical
OUTPUT IMPEDANCE: 50 ohm nominal
MISMATCH TOLERANCE:
100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. See Application Note #27.
MODULATION CAPABILITY: Will faithfully reproduce AM, FM, or pulse modulation appearing on the input signal
NOISE FIGURE: 8 dB maximum, 6 dB typical
HARMONIC DISTORTION: -20 dBc maximum at 100 watts, -0dBc typical @ 100 watts
THIRD ORDER INTERCEPT POINT: 58 dBm typical
Remote Interfaces:
- IEEE-488, 24 pin female
- RS-232, 9 pin Subminiature D (female)
- Fiber Optic, ST Conn Tx and Rx RS-232
- USB 2.0, Type B
- Ethernet, RJ-45
The Model 150W1000B is a solid-state, self-contained, air-cooled, broadband amplifier designed for applications where instantaneous bandwidth, high gain and linearity are required. Available in a stylish, contemporary cabinet for benchtop use or with cabinet removed for rack mounting.
The Model 150W1000B, when used with a sweep generator, will provide 150 watts of RF power. Included is a front panel gain control which permits the operator to conveniently set the desired output level. The 150W1000B is protected from RF input overdrive by an RF input leveling circuit which controls the RF input level to the RF amplifier first stage when the RF input level is increased above 0dBm. The RF amplifier stages are protected from overtemperature by removing the DC voltage to them if an over-temperature condition occurs due to cooling blockage or fan failure. The Model 150W1000B is equipped with a Digital Control Panel (DCP) which provides both local and remote control of the amplifier. The DCP uses a color LCD touch screen display to indicate the operate status and fault conditions if an over-temperature or power supply fault has occurred. The unit can be returned to operate when the condition has been cleared.
All amplifier control functions and status indications are available remotely through the included Remotes Package. The Remotes Package includes GPIB/IEEE-488 format, RS-232 hardwire and fiber optic, USB, and Ethernet.
The Model 150W1000B is a solid-state, self-contained, air-cooled, broadband amplifier designed for applications where instantaneous bandwidth, high gain and linearity are required. Available in a stylish, contemporary cabinet for benchtop use or with cabinet removed for rack mounting.
The Model 150W1000B, when used with a sweep generator, will provide 150 watts of RF power. Included is a front panel gain control which permits the operator to conveniently set the desired output level. The 150W1000B is protected from RF input overdrive by an RF input leveling circuit which controls the RF input level to the RF amplifier first stage when the RF input level is increased above 0dBm. The RF amplifier stages are protected from overtemperature by removing the DC voltage to them if an over-temperature condition occurs due to cooling blockage or fan failure. The Model 150W1000B is equipped with a Digital Control Panel (DCP) which provides both local and remote control of the amplifier. The DCP uses a color LCD touch screen display to indicate the operate status and fault conditions if an over-temperature or power supply fault has occurred. The unit can be returned to operate when the condition has been cleared.
All amplifier control functions and status indications are available remotely through the included Remotes Package. The Remotes Package includes GPIB/IEEE-488 format, RS-232 hardwire and fiber optic, USB, and Ethernet.